Відео

Yes, you can have both outputs active at the same time!

We currently do not have a special tutorial for DirectWIRE Loopback of GIGAPORT eX, however this article in our Knowledge Base might help: kb.esi.ms/KB00300EN ... essentially, you can record in any audio application everything that any (also other) audio application plays via channel 1/2.

​@@ESIaudio Thank you for your response. Based on this information, how can I record my DJ set on Traktor Pro?

@@ggozdilBasically you can use any audio application for recording, launch it alongside Traktor DJ and record the input 1/2 channel provided by GIGAPORT eX.

The concept of MAYA22 USB is that there is no gain knobs to keep the product as small as possible. The gain / volume control is done by software. If you look for an interface with nice hardware controls, you might want to look at our U22 XT or Amber i1.

Unfortunately the iPhone does not provide enough power for a device like UGM192, especially not when a microphone with phantom power is being used. Because of that, we provide a separate power connector that allows you to connect a separate power supply, which could also be a portable battery.

Thank you for purchasing Amber i1. This video describes something different than what you are trying to do. We do not have a tutorial for your specific application at the moment, however this video comes close and might be interesting: ua-cam.com/video/waQX9X8rvjg/v-deo.html - it is about vocal recording with Bitwig Studio 8-Track as multichannel DAW, which is included with our interfaces. Your application is very basic and does not require many settings. Do not set anything in DirectWIRE, no connections at all. In Audacity make sure to select the input 1/2 channel of Amber i1 as recording device. Now when you record, when the input on the hardware is set to “Mic”, both channels will be your vocals. When set to “Hi-Z”, both channels will be your guitar. And when set to “Mic/Hi-Z”, then the left channel are the vocals and the right channel the guitar. This assumes you record in stereo. If you record in mono, only the left input channel will be recorded. Audacity is a stereo editing software (similar to the included Wavelab LE), so it depends on exactly what you want to do, if this is enough. If you want to properly record multiple sources (i.e. add pre recorded stuff, other instruments or like show in this video UA-cam content) and/or several takes of your vocals / guitar playback, you really need to consider using a multichannel DAW instead. We include Bitwig Studio 8-Track, but the principle is the same for any software. You can then record vocals on one track, guitar on another, other signals like UA-cam on additional ones, add virtual instruments, add effects, mix the sound the way you like it to left/right channels, etc. - and eventually export a final song created from different recordings and sources. This is all very basic stuff that works the same with different software and other audio interfaces and there are many recording tutorials available online. Also if you have specific issues with Amber i1, do not hesitate to contact our tech support as each application is different and it is not easy to generalize what to setup exactly as everyone is doing something slightly different. I hope this helps a bit to point you into the right direction.

@@ESIaudio Thank you very much!

Yes, in fact this is what MoCo is intended to be used with. You connect it between your source (usually your audio interface) and one or two pairs of monitors. If you use two pairs, then you can switch between them. MoCo itself is passive (= it does not change the sound) while your monitors are active (= they amplify the signal to produce the sound needed for the speakers).

@@ESIaudio Thanks for your detailed answer. I am going to buy it today . Have a nice time

Unfortunately website is currently unavailable due to a larger outage at our web hosting provider. According to the info we received, they are working to resolve the problem but they could not provide an ETA when everything is back up and running again. We are keeping our fingers crossed! We apologise for the inconvenience and we are available for support questions, product information and driver software via info@esi-audio.com. Your ESI Audio Team!

Hi @szmodry! We would like to refer you to our DirectWIRE tutorials. If you can't find what you're looking for here, you can also contact our technical support for a detailed explanation: info@esi-audio.com

I think you might be positively surprised :)

Thank you to consider uniK 05+ for that. Yes, 2m is a good distance for a near field monitor like these and you should not get any fatigue problems when using them for a long time.

@ShortTimeStorys The button on the back switches between the inputs on the front and the inputs on the rear of U22 XT. If you want to use the microphone input, of course you must set it to the front inputs since the microphone input is on the front. What you hear (= monitoring) is a different issue: the InMixOut knob on the front controls if you only hear what is coming in (= In), what you play from the computer (= Out) or both together (= Mix).

Hello @danibass25, the issue you mentioned can have several reasons and without more details, we can only guess what exactly is happening. The peal LED being on constantly means that the signal is very high in level, so it is possible that the gain of input 2 has to be lowered (i.e. what happens if the gain is set all the way to 0, is the LED off then?) or it could mean that the signal itself is "too hot", so we would have to look at the source (is it the output of an electric guitar?). Then you said you cannot hear it, however as there is a red LED, some signal must be there (even if it is too loud or noise, etc.) - so it looks to me like you did not setup the monitoring to be able to hear the "Hi-Z" signal. To do that, you would need to set the "inMixOut" knob to the middle or all the way to "In" and the input source switch must be set to Hi-Z or Mic/Hi-Z. Also the front inputs must be selected. All of this is explained also on our Knowledge Base under kb.esi-audio.com/ and of course for any issues like this it is best to use our technical support via www.esi-audio.com/support ... if English is a problem, you can use translation tools like Google, etc. that work really well these days. Finally, if you need support locally in your local language, you can contact our distributor in Argentina and you do not need to pay anything for them to check this issue together with you. You can find the contact information our website via About Us > Distributors.

@@ESIaudio Hi, how are you? Yes, I have already done everything you mentioned long before and the problem persists, I want to clarify that the interface has never suffered any physical damage either, so I already wrote an email more than a month and a half ago to receive a solution from their support No answers yet, only a person named Andreas answered me, giving me the same instructions, who did not respond to my emails again, which is why I went here to UA-cam, believe me, I have looked for solutions of all kinds without an apparent solution, and to be frank I feel disappointed by the brand and this product, which, as I mentioned, cost me a lot of money considering that I live in Argentina, and I am also not able to record or work on anything because the interface does not allow it, I want to highlight I make a living from music, it is my profession, and this problem has meant I lost more than 2000 dollars in work that I could not do as a session player given this problem and I would very much like to receive some compensation for all this, I also went to distributors in Argentina which seem deaf and dumb since they do not respond to any message, in this way I find myself here exhausting my resources to contact someone in charge of the ESI company to know what answer they are going to give me, the truth is that it hurts me to make a claim for a youtube comment and I just hope you help me, I appeal to your good faith and I hope that you appeal to my good faith for this, I am not trying to get anything (although a better quality interface would not be a bad idea to compensate for all my time and money lost) but I have been trying to find a definitive solution for a long time, but with all the money and patience that I have lost due to a bad interface my hopes for compensation from you are weak, I want to believe that ESI company takes care of its customers everyone and they will understand my situation, I want to believe that the system to make a claim works, and that ESI provides me with a quality interface to work with since I do not have another interface, I can only record my sessions for my clients with the computer and the instrument connected directly, which does not give a quality sound, without further ado, thank you ESI for taking the time to write to me, I would like to highlight that I have already gone to ESI distributors in Argentina without result, I prefer to speak with ESI international directly since I master the English language, I attach my WhatsApp number +5493518736421 and my Instagram is @danibass25, without further ado, thank you very much again and I am waiting for a response, as I said before I want to believe that a user who bought an ESI confidently also It gives help and not just to some person or UA-camr because they are famous.

@@ESIaudio here some videos drive.google.com/file/d/1DyIFUDYsv2IU4pFPUu-1v6Dddg5HZI4t/view?usp=drive_link

@@ESIaudio here an another video drive.google.com/file/d/1DyTqAoUHsTGB5uRO1lHNdXFHXWqs7dXB/view?usp=drive_link

@@danibass25 I think you must have received a reply from our technical support with more detailed information. Please contact us at anytime via our tech support if you have any issues with U22 XT.

Hi! We are sorry that you are not satisfied with the U22 XT cosMik set. Of course, it does not meet our requirements. What exactly don't you like about the product? We are always open for improvement. If it's not too much trouble, you can send us an e-mail at info@esi-audio.com. We are confident that we can resolve the issue quickly. Thank you for your feedback!

Ji @rautshsale1948! The RCA inputs are a -10dBV line input. By definition the levels are fixed. If needed, levels can be adjusted by software.

@@ESIaudio thanks for the quick reply and/but sry for the followup. does this mean, if i want to plug in the stereo line out of my mixer to the RCA inputs, would i just select inputs 3/4 in the DAW, and both L&R would have the same input level (-10dBV)? so practically speaking, i'd just have to worry about the output level on my mixer to hit the right level, but if necessary, i can still adjust the input level (for both L&R channels at the same time) via the software? i just want to get away from manually setting input gain for L&R channels individually, when recording a stereo channel, hence my questions. thanks in advance!

@@rautshsale1948 You would use input 1/2 as U22 XT is a 2 in / 2 out audio interface and to use the line inputs on the rear, you select it via the Front/Back selection switch of the hardware. Since your source is a mixer, you will have the best quality and dynamic range if you adjust the output level of your mixer rather than the input of U22 XT via software.

Hi... ...yes of course, there is hardware direct monitoring on the front panel of the U22 XT

@@ESIaudio Ok.. Btw i had some issue.. why my mic cant setting at 9600hz? its going to sound like speed up/bug voice when recording..

@@razmanrhoads2078 This sounds like a mismatch of the sample rate inside your audio application ... for instance if the software is set to a different sample rate than the audio hardware something like this could happen. Since this is very specific to what exactly you are doing (audio software, OS version, etc.), please contact our tech support via www.esi-audio.com/support if the problem is still there.

The inputs must also be enabled in the Bitwig preferences. If you have already done this and are still not getting an input signal, you can use the front/back input selector switch on the back of the U22 XT. If none of this works, please feel free to contact our support team www.esi-audio.com/support/

Please contact our support team at www.esi-audio.com/support/

It should be impossible that switching the mic gain makes nearly no difference, i.e. that means something is wrong. Maybe the XLR to TRS cable has a problem. Can you contact our technical support via www.esi-audio.com/support ?

@@ESIaudio I wanted to know if you can connect 2 pairs of headphones to this model?

@@Niqem No, it is not possible to connect 2 pairs of headphones to the UGM 192. In this case we would recommend a headphone amplifier. This would make it possible.

Since our products are made for audio using components for audio, we cannot guarantee to reproduce sound above 22kHz. You can contact our technical support team if you need more info or specs: www.esi-audio.com/support

Yes!

You can contact our technical support team www.esi-audio.com/support

Dante isn't supported on Linux.

2ms in Guitar rig, very fast, 32 buffer size

Sorry about that, but this is not possible with DirectWIRE. The DirectWIRE Device routing function is to route audio signal between different audio apps and driver standards. To remove background noise you need a DAW software or a audio denoiser app.

@@ESIaudio ok, thank you for the reply

Hello! Yes, Gigaport eX works with OS X / mac OS (10.9 and above) and with native CoreAudio support (32-bit and 64-bit) If you need more information, take a look here: www.esi-audio.com/products/gigaportex/

I am sorry you are having problems. This is not something that can generally be answered since this sounds very general and we need to know a lot more details about your system configuration (computer, operating system, software used, etc.) ... also which ESI product you are using. You can have a look at our knowledge base kb.esi-audio.com/ and if there is nothing you can find, please contact our technical support via www.esi-audio.com/support/

@@ESIaudio I know the buttons should appear green, not orange-red. They appeared orange-red to me, and when I turn the volume down, they only flicker slightly green.

@@mihaela449 I assume you refer to the LED indicators that show the input level? If they are red, the signal is clipping and too loud. Orange is OK, then you are close to clipping and green shows it is a lower level and there is a signal. However, we still do not know what you are actually trying to do and what ESI products you are using. The best way is to explain what the problem is, what you are trying to do and what product from us with what software you are using and contact our tech support with that info: www.esi-audio.com/support/

There are 4 stereo outputs, so yes of course you can play 4 channels from Traktor.

@@ESIaudio yes brooo thank you i buy today this interface thank you ;) enjoy is this interface have clear sound i have yamaha hs8 studio monitors i think with this interface will be good and amazing sound??

No. Only through the outputs of the interface you can send out signals related to the audio processing, due to performance and latency related issues. It is theoretical with some software (usually anything that is not using ASIO) possible to output signals through the onboard sound card of your computer but the performance and stability will never be acceptable. When you use a professional audio interface, you also need to use its outputs.

UGM192 has a second USB port that can be connected to a power supply, so whenever the power from the computer or iPad, etc. will not be enough, you can use this second port to supply power to UGM192 either through a power adapter or a battery pack.

@@ESIaudio Thanx!!!!